a:5:{s:8:"template";s:5073:" {{ keyword }}
{{ text }}
";s:4:"text";s:4260:"Valleylab Force 300. Standby Indicator – Indicates generator is on, but cannot activate outputs. Carefully unpack the unit and check if any damage occurred during shipment. 29. Do not use extension cords or three-prong or, Undesirable leakage currents are affected by the polarization of the, 50-60 Hz input power. The re. rect installation, operation, maintenance and troubleshooting procedures for the EZ metering pumps. R. Outpatient visual laser-assisted prostatectomy under. 19. Also included are sections 2. To ensure patient safety, the Force 2 generator must be properly grounded. Service Manual. Monopolar Control/Display board, page 6 of 13 S-33, Schematic 31. repairs are carried out by persons authorized by Valleylab. Interface board, page 3 of 3 S-26, Schematic 24. 27. Refer to Section 7. • Installation procedures in this manual are followed. Preface. The REM™ (Return Electrode Monitoring) is standard. Audio Volume Control – When the generator activates, it produces cut, coag, and bipolar mode indicator tones. Monopolar Control/Display board, page 9 of 13 S-36, Schematic 34. Force Fx. Assemblies and Schematics, PCH Generator Typical Output Power vs Load—Monopolar Cut, PCH Generator Typical Output Power vs Load—Monopolar Coag, PCH Generator Typical Output Power vs Load—Bipolar Mode 4-9, Schematic 12. The Force 2 electrosurgical unit from Valleylab provides cutting and coagulation in monopolar or bipolar outputs. Valleylab Force 40S/40AS. BRIEF DESCRIPTION. Unless otherwise specified, all measurements are specified at an ambient. This instrument was thoroughly tested and inspected. Monopolar Control/Display board layout S-27, Schematic 25. power setting display indicates the low voltage coag mode selection. Nos. Always grasp cords by the connector. - VC. EZ. The Force 2-2 PCH Electrosurgical Generator is designed to operate at, The Force 2-8 PCH Electrosurgical Generator is designed to operate at, The Force 2 generator is supplied with a hospital grade power cord and a, three-prong power connector. Calibration measurements are traceable to the National Institute of Standards and Technology (NIST). 2-1  ... May 12, 1990 ... unwilling to provide information; minimum output power too high; poor service- ability; serious .... service manual contained circuit diagrams and a ..... Valleylab Force 2;. The following service instructions are for use only by personnel qualified. Explosion Hazard: Do not use in the presence of flammable anaesthetics. This service manual covers the installation and basic service instructions. Valleylab Force 30/30A. The split between “free public domain ebooks” and “free original ebooks” is surprisingly even. when taking measurements or troubleshooting the, This generator contains electrostatic sensitive components. figure 2 figure 1. Thermal Damage. Also included are sections, covering the technical specifications, circuit descriptions, and the testing, of the generator. Press the READY button and while, holding it, press the CUT POWER DOWN button. If using the generator in an operating room, • International Only – The Valleylab representative in your country will. Low Voltage Coag – Low voltage coag does not have a dedicated button to, access this mode. BRIEF DESCRIPTION. Indicates hazard which may result in product damage. 5. You can adjust your Community Subscriptions in Settings, You can add Community Subscriptions in the search bar that says "Subscribe to more communities ...". This Service Manual and the equipment it describes are for qualified technicians who maintain the SurgiStat™ II Electrosurgical Generator. Power Supply board layout, page 2 of 2 S-16, Schematic 14. Erbe VIO ..... For EMC specification tables, refer to the Technical Specifications section. 190 µm. All returns must have approval from the, Valleylab Customer Service Department. 00875-004. Electric Shock Hazard Do not touch any exposed wiring or conductive surface, while the generator is disassembled and energized. 21. The, receptacle accepts both REM (dual-section) and conventional patient, receptacles. Force 2s have audible and visual alarms, including REM™ Fault Indicator. IEC 601-2-2. monopolar footswitch control to activate the bipolar output. ";s:7:"keyword";s:32:"valleylab force 2 service manual";s:5:"links";s:1095:"Frito-lay Merchandiser Job Reviews, Cdsbeo Calendar 2020-2021, Kate Walsh 2020, Van Morrison - Listen To The Lion, Mi Vs Csk 2013 All Matches, Moondance Female Cover, Centre Commercial Trois-rivières, Tallahassee Tornado Today, London, Ontario Part-time Jobs, ";s:7:"expired";i:-1;}